Sign in

Sign in
Reset PasswordCreate an Account

Create an Account

Create an Account
Sign in

1000M Copper SFP

ASCENT’S SFP-AG-CO-01 1000 BASE-T Copper Small Form Pluggable (SFP) transceivers are based on the SFP Multi Source Agreement (MSA). They are compatible with the Gigabit Ethernet standards as specified in IEEE Std. 802.3. The 1000 BASE-T physical layer IC (PHY) can be accessed via I2C, allowing access to all PHY settings and features.

•    Up to 1.25 Gb/s bi-directional data links

•    Hot-pluggable SFP footprint

•    Low power dissipation(1.05W typical)

•    Compact RJ-45 connector assembly

•    Fully metal enclosure, for lower EMI

•    RoHS compliant and lead-free

•    Single +3.3V power supply

•    1.25 Gigabit Ethernet over Cat 5 cable


3.3V Volt Electrical Power Interface

The SFP‑AG‑CO‑01 has an input voltage range of 3.3 V ± 5%. The 4V maximum voltage is not allowed for continuous operation.

Parameter

Symbol

Min

Typ

Max

Unit

Notes/Conditions

Supply Current

Is


320

375

mA

1.2W max power over full range of voltage and temperature.

See caution note below

Input Voltage

Vcc

3.13

3.3

3.47

V

Referenced to GND

Maximum Voltage

Vmax



4

V


Surge Current

Isurge



30

mA

Hot plug above steady state current. See caution note below

Caution: Power consumption and surge current are higher than the specified values in the SFP MSA

Low‑Speed Signals

MOD_DEF(1) (SCL) and MOD_DEF(2) (SDA), are open drain CMOS signals (see section VII, "Serial Communication Protocol"). Both MOD_DEF(1) and MOD_DEF(2) must be pulled up to host_Vcc

Parameter

Symbol

Min

Max

Unit

Notes/Conditions

SFP Output LOW

VOL

0

0.5

V

4.7k to 10k pull‑up to host Vcc, measured at host side of connector

SFP Output HIGH

VOH

host_Vcc ‑ 0.5

host_Vcc + 0.3

V

4.7k to 10k pull‑up to host_Vcc, measured at host side of connector

SFP Input LOW

VIL

0

0.8

V

4.7k to 10k pull‑up to Vcc, measured at SFP side of connector

SFP Input HIGH

VIH

2

Vcc + 0.3

V

4.7k to 10k pull‑up to Vcc, measured at SFP side of connector


High‑Speed Electrical Interface, Transmission Line‑SFP

All high‑speed signals are AC‑coupled internally.

Parameter

Symbol

Min

Typ

Max

Unit

Notes/Conditions

Line Frequency

fL


125


MHz

5‑level encoding, per IEEE 802.3

Tx Output Impedance

Zout,TX


100


Ω

Differential, for all frequencies between 1MHz and 125MHz

Rx Input Impedance

Zin,RX


100


Ω

Differential, for all frequencies between 1MHz and 125MHz

High‑Speed Electrical Interface, Host‑SFP

Parameter

Symbol

Min

Typ

Max

Unit

Notes/Conditions

Single‑Ended Data Input Swing

Vinsing

250


1200

mV

Single‑ended

Single‑Ended Data Output Swing

Voutsing

350


800

mV

Single‑ended

Rise/Fall Time

Tr,Tf


175


psec

20 % to 80 %

Tx Input Impedance

Zin


50


Ω

Single‑ended

Rx Output Impedance

Zout


50


Ω

Single‑ended

General Specifications

Parameter

Symbol

Min

Typ

Max

Unit

Notes/Conditions

Data Rate

BR

10


1000

Mb/sec

IEEE 802.3 compatible.

See Notes 2 through 4 below

Cable Length

L



100

m

‑12

Category 5 UTP. BER <10

Notes:

1. Clock tolerance is ±50 ppm

2. By default, the SFP‑AG‑CO‑01 is a full duplex device in preferred master mode

3. Automatic crossover detection is enabled. External crossover cable is not required

4. SFP does not support SGMII .With a SERDES the module will operate at 1000BASE‑T only.

Parameter

Symbol

Min

Typ

Max

unit

Notes/Conditions

Case Operating Temperature

Tcase

0


70

°C

SFP‑AG‑CO‑01

‑10


80

°C

SFP‑AG‑CO‑01E

‑40


85

°C

SFP‑AG‑CO‑01A

Storage Temperature

Tsto

‑40


85

°C

Ambient temperature


Serial Communication Protocol Bus Timing Requirements

SFP‑AG‑CO‑01 supports the 2‑wire serial communication protocol outlined in the SFP MSA. It uses an Atmel AT24C02B 256 byte EEPROM with an address of A0h.

Parameter

Symbol

Min

Typ

Max

unit

Notes/Conditions

I2C Clock Rate


0


100,000

Hz


 


image1.jpeg

Series Recommendation
Related Information

Get in touch with our experts

Feedback