ASCENT SFPP-ATLP-85-03 transceivers support the 2-wire serial communication protocol as defined in the SFP+ MSA.
• Applicable for 10GBASE-SR/SW and 10G Ethernet networks
• Compliant to SFP+ SFF-8431
• Compliant to 802.3ae 10GBASE-SR standard
• RoHS,FCC Compliant
• Compatible with Juniper
• Case operating temperature range: Commercial: 0 to 70°C
Industrial: -40 to 85°C
Absolute Maximum Ratings
Parameter | Symbol | Min. | Typ. | Max. | Unit | Note |
Storage Temperature | Ts | ‑40 | ‑ | 85 | °C | |
Relative Humidity | RH | 5 | ‑ | 95 | % | |
Power Supply Voltage | VCC | ‑0.3 | ‑ | 4 | V | |
Signal Input Voltage | Vcc ‑ 0.3 | ‑ | Vcc + 0.3 | V |
Recommended Operating Conditions
Parameter | Symbol | Min. | Typ. | Max. | Unit | Note |
Case Operating Temperature | Tcase | 0 | ‑ | 70 | °C | Commercial |
‑40 | ‑ | 85 | °C | Industrial | ||
Power Supply Voltage | VCC | 3.14 | 3.3 | 3.47 | V | |
Power Supply Current | ICC | ‑ | 300 | mA | ||
Data Rate | BR | 10.3125 | Gbps | |||
Transmission Distance | TD | ‑ | 300 | m | ||
Coupled Fiber | Multi‑mode fiber | 50/125 µm MMF |
Optical Characteristics
Parameter | Symbol | Min | Typ | Max | Unit | Ref. |
Transmitter | ||||||
Output Optical Power | POUT | ‑7.3 | ‑1 | dBm | 1 | |
Optical Wavelength | λ | 840 | 850 | 860 | nm | |
Optical Extinction Ratio | ER | 3.0 | dB | |||
RIN | RIN | ‑128 | dB/Hz | |||
Output Eye Mask | Compliant with IEEE 802.3ae | |||||
Receiver | ||||||
Rx Sensitivity | RSENS | ‑11.1 | dBm | 2 | ||
Input Saturation Power (Overload) | Psat | 0.5 | dBm | |||
Wavelength Range | λC | 770 | 850 | 860 | nm | |
LOS De‑Assert | LOSD | ‑12 | dBm | |||
LOS Assert | LOSA | ‑30 | dBm | |||
LOS Hysteresis | 0.5 | dB |
Notes:
1. Class 1 Laser Safety per FDA/CDRH and IEC‑825‑1 regulations.
2. Measured with a PRBS 231‑1 test pattern, @ 10.325 Gb/s, BER<10-12.
Electrical Characteristics
Parameter | Symbol | Min | Typ | Max | Unit | NOTE |
Supply Voltage | Vcc | 3.14 | 3.3 | 3.46 | V | |
Supply Current | Icc | 300 | mA | |||
Transmitter | ||||||
Input Differential Impedance | Rin | 100 | Ω | 1 | ||
Single‑ended Data Input Swing | Vin, pp | 180 | 700 | mV | ||
Transmit Disable Voltage | VD | Vcc–1.3 | Vcc | V | ||
Transmit Enable Voltage | VEN | Vee | Vee + 0.8 | V | 2 | |
Receiver | ||||||
Differential Data Output Swing | Vout, pp | 300 | 850 | mV | 3 | |
LOS Fault | VLOS fault | Vcc–1.3 | VccHOST | V | 5 | |
LOS Normal | VLOS norm | Vee | Vee+0.8 | V | 5 | |
Power Supply Rejection | PSR | 100 | mVpp | 6 |
Notes:
1. Connected directly to TX data input pins. AC coupled thereafter.
2. Or open circuit.
3. Into 100 Ω differential termination.
4. These are unfiltered 20‑80% values
5. Loss of Signal is LVTTL. Logic 0 indicates normal operation; logic 1 indicates no signal detected.
6. Receiver sensitivity is compliant with power supply sinusoidal modulation of 20 Hz to 1.5 MHz up to specified value applied through the recommended power supply filtering network.
Regulatory Compliance
Feature | Reference | Performance |
Electrostatic Discharge (ESD) | IEC/EN 61000‑4‑2 | Compatible with standards |
Electromagnetic Interference (EMI) | FCC Part 15 Class B EN 55022 Class B (CISPR 22A) | Compatible with standards |
Laser Eye Safety | FDA 21CFR 1040.10, 1040.11 IEC/EN 60825‑1, 2 | Class 1 laser product |
Component Recognition | IEC/EN 60950, UL | Compatible with standards |
ROHS | 2002/95/EC | Compatible with standards |
EMC | EN61000‑3 | Compatible with standards |
10 Gb/s 1310nm SFP+ 40 km Transceiver
SFPP-ATLP-31-20 SFP+ Plug-in, 10Gbps, 20km, TX=1310/RX wide, on two single mode fibers, LC/PC Blue
SFPP-ATLP-31-10 SFP+ Plug-in, 10Gbps, 10km, TX=1310/RX wide, on two single mode fibers, LC/PC Blue
SFPP-ATLP-31-02 10Gb/s 1310nm SFP+ 2 km Transceiver
SFPP-ATLP-51-40 10 Gb/s 1550 nm SFP+ 40 km Transceiver
SFPP-ATLP-51-100 10 Gb/s 1550 nm SFP+ 100 km Transceiver
SFPP-ATLP-51-80 10 Gb/s 1550 nm SFP+ 80 km Transceiver
SFPP-LP-T99R-80 10 Gb/s Tunable DWDM SFP+ 80 km Transceiver
SFPP-ATLP-DXX-80 10 Gb/s DWDM SFP+ 80 km Transceiver
SFPP-ATLP-DXX-40 SFP+ Plug-in, 10Gbps, 40km, TX=ITU Ch xx (17 to 61) /RX wide, on two single mode fibers, LC/PC Blue
SFPP-ATLP-CXX-80 SFP+ Plug-in, 10 Gbps, 80 km, TX = CWDM Ch xx (1470 nm to 1610 nm)/RX wide, on two single-mode fibers, LC/PC Blue.
SFPP-AT-LP-XXXX-60D 10 Gb/s BIDI SFP+ 60 km Transceiver
SFPP-ATLP-CXX-40 SFP+ Plug-in, 10Gbps, 40km, TX=CWDM Ch xx (1270 nm to 1610 nm) /RX wide, on two single mode fibers, LC/PC Blue
SFPP-ATLP-CXX-10 SFP+ Plug-in, 10 Gbps, 10 km, TX=CWDM Ch xx (1270 nm to 1610 nm)/RX wide, on two single-mode fibers, LC/PC Blue
SFPP-AT-LP-XXXX-40 SFP+ Plug-in, 10Gbps, 40km, TX=1270/RX=1330 , on one single mode fibers, LC/PC Blue
SFPP-LP-XXXX-10 SFP+ Plug-in, 10Gbps, 10km, TX=1270/RX=1330 , on one single mode fibers, LC/PC Blue
XFP-AT-LP-31-20 10 Gb/s 20 km XFP Transceiver
XFP-AT-LP-31-10 10 Gb/s 10 km XFP Transceiver
XFP-AT-LP-51-40 10 Gb/s 40 km XFP Optical Transceiver
XFP-AT-LP-51-80 10 Gb/s 80 km XFP Optical Transceiver
XFP-ATLP-XXXX-60 10 Gb/s BIDI XFP 60 km Transceiver
SFPP-AT-CO-02 10GBASE-T SFP+ Copper RJ45 30m Transceiver
SFPP-ATLP-61-80 SFP+ Plug-in, 10Gbps, 80km, TX=1610/RX wide, on two single mode fibers, LC/PC Blue
SFPP-AT-CO-03 10GBASE-T SFP+ Copper RJ45 30m Transceiver
SFPP-16-LP-85-01 16 Gb/s 850 nm SFP+ 100 m Transceiver
SFPP-A8LP-85-015 8.5 Gb/s 850 nm Multi-Mode SFP+ Transceiver
SFPP-A6-LP-31-02 6.25 Gb/s Single-Mode SFP+ Transceiver
SFPP-A6-LP-85-03 6.25 Gb/s 850 nm Multi-Mode SFP+ Transceiver
Get in touch with our experts
Feedback